Electrolux E774F402BI Bedienungsanleitung

E774F402BIEN Washing Machine User Manual

The inlet hose1. Remove the inlet hose from inside thedrum.2. To connect the water inlet hose towardsthe proper direction and with the properinclinati

Ø 40 mmTo a stand pipe with vent-holeDirectly into a drain pipe at a height of notless than 60 cm (23.6”) and not more than100 cm (39.3”).The end of t

553 mm596 mm140 mm76 mm50 mm50 mm819 mmIf hoses run behind theappliance, make sure thatnothing closes the smallrecess indicated with themeasures 50 x

1. Remove the screws of the top cover on therear of the appliance and install the anti-tiltingdevice as shown in the drawing.~10mm2. Adjust the anti-t

Reversibility of the cupboard doorCarry out the cupboard door reversibilitybefore the appliance is built in completely.MNOIf the cupboard door has to

16-22 mm22±1,5 mm416mm595-598 mmØ 35 mm14 mmSet the position of the lower hole respectingdimensions and distances shown in thedrawing (449 mm).Counter

2N1EDCCounter-magnetThe appliance is pre set for a magneticclosure.For a correct closure:1. Position the screw C and the counter-magnet D on the magne

5. CONTROL PANEL5.1 Control panel descriptionTemp.Spin Prewash Soft Plus Plus SteamDelayStartTimeManager90°60°40°30°20°Cold14001200800CottonsSynthetic

Delay start indicator.The digital indicator can show:• Reset position ( ).• Programme duration (e. g. ).• Delay time (e. g. ).• Cycle end ().• Warni

6.4 Temp. When you select a washing programme,the appliance automatically proposes adefault temperature.The indicator Cold = cold water.The indicator

CONTENTS1. SAFETY INFORMATION...32. SAFETY INSTRUCTIONS...

This option increases theprogramme duration.The corresponding indicator above thetouch button illuminates and also stayspermanently on during next cyc

very quick cycle for a smaller lightlysoiled load (max. half loadrecommended). the shortest cycle to freshen up asmall amount of laundry.The Time Man

ProgrammeDefault tem‐peratureTemperaturerangeReferencespinspeedMaxi‐mumloadProgramme description(Type of load and soil level)Synthetics40 °C60 °C - Co

ProgrammeDefault tem‐peratureTemperaturerangeReferencespinspeedMaxi‐mumloadProgramme description(Type of load and soil level)Steam-1 kg Cottons, Synth

ProgrammeDefault tem‐peratureTemperaturerangeReferencespinspeedMaxi‐mumloadProgramme description(Type of load and soil level)Outdoor30 °C40 °C - Cold1

ProgrammeDefault tem‐peratureTemperaturerangeReferencespinspeedMaxi‐mumloadProgramme description(Type of load and soil level)Wool/Silk40 °C40 °C - Col

ProgrammeSpinNoSpinPrewash1) 2)Soft PlusPlus Steam3)Delay StartTime ManagerRapid 14min Sport Outdoor

9. BEFORE FIRST USE1. Make sure that the electrical power isavailable and the water tap is open.2. Pour 2 litres of water into thedetergent compartmen

- Maximum level for quantity ofliquid additives. - Flap for powder or liquid deter‐gent.Always follow theinstructions that you find onthe packaging o

display and the given informationchanges accordingly.If a selection is not possiblean acoustic signal soundsand the display shows.10.6 Starting a prog

1. SAFETY INFORMATIONBefore the installation and use of the appliance, carefullyread the supplied instructions. The manufacturer is notresponsible f

10.10 Cancelling a runningprogramme1. Press the button On/Off to cancel theprogramme and to deactivate theappliance.2. Press the button On/Off again t

2. Press the Start/Pause button: theappliance drains the water and spins.The option indicator Rinse Hold or disappears.If you have set Quiet and

11.3 Detergents and othertreatments• Only use detergents and othertreatments specially made forwashing machines:– powder detergents for all types offa

12.3 Maintenance washThe repeated and prolonged use of lowtemperature programmes can causedetergent deposits, fluff residues,bacterial growth inside t

2. Remove the top part of the additivecompartment to aid cleaning andflush it out under running warmwater, to remove any traces ofaccumulated detergen

121. Open the pump cover.2. Place a suitable bowl below the drain pumpaccess to collect the water that flows out.Always keep a rag nearby to dry up an

7. If it is necessary, remove fluff and objectsfrom the filter recess.Make sure that the impeller of the pump canrotate. If it does not rotate, contac

12.8 Cleaning the inlet hose and the valve filter12345°20°12.9 Emergency drainIf the appliance cannot drain the water,carry out the same procedure, de

13.1 IntroductionThe appliance does not start or it stops during operation.First try to find a solution to the problem (refer to the table). If the pr

13.2 Possible failuresProblem Possible solutionThe programme doesnot start.• Make sure that the mains plug is connected to themains socket.• Make sure

– by clients in hotels, motels, bed & breakfast andother residential type environments;– areas for communal use in blocks of flats or inlaunderett

Problem Possible solutionThere is water on thefloor.• Make sure that the couplings of the water hoses aretight and there is not water leakages.• Make

13.3 Emergency door openingIn case of power failure or functioningfailure the appliance door remainslocked. The washing programmecontinues when the po

Programmes Load(kg)Energycon‐sumption(kWh)Watercon‐sumption(litre)Approxi‐mate pro‐grammeduration(minutes)Remain‐ing mois‐ture (%)1)Cottons60°C7 1.20

Water supply 2)Cold waterMaximum Load Cotton 7 kgEnergy Efficiency Class A+++Spin Speed Maximum 1351 rpm1) The appliance works correctly if the water

Remaining moisture content in % 52The 'standard 60 °C cotton programme' and the'standard 40 °C cotton programme' are the standardw

ENGLISH 45

www.electrolux.com46

ENGLISH 47

www.electrolux.com/shop157018070-B-292018

than 0°C or where it is exposed to theweather.• The floor area on which the applianceis to be installed must be flat, stable,heat resistant and clean.

• Do not touch the glass door while aprogramme is in operation. The glasscan get hot.2.5 Service• To repair the appliance contact anAuthorised Service

1. Put two polystyrene packagingelements on the floor under theappliance.WARNING!It is stronglyrecommended that thisaction is carries out by twoperson

6. Remove the three bolts, the hoseholders and plastic spacers by using thespanner supplied with the appliance.FG7. Close the holes with the plastic c

3.5 Positioning and levellingx41. Install the appliance on a flat hard floor.WARNING!Make sure that carpets do notstop the air circulation belowthe ap