Electrolux TM-75 Betriebsanleitung PDF herunterladen (Seite 13)

WATER

TUBING REMOVAL

(Fig's

10, 11)

Plastic

tubing connects

the water

pump

to the blade

guard.

The fittings

used

to connect

this tubing seal and

grip

the outside diameter

of the

tubing. Special internal

locking

fingers attached

to the flanged

collet

hold

the

tubing fast. To

clean the water

tubing requires

the

tubing

to be

removed

from

the fittings. To release

the

tubing form

the fitting, fully

depress

the collet

before

pulling

the tube out of

the

fitting.

When

you press

down

on the collet

you

are

opening the locking fingers

and freeing

the tubing

to be easily removed.

WATER

TRAY

REMOVAL AND

INSTALLATION

THE

REMOVAL

AND INSTALLATION

OF THE

WATER

TRAY IS

EASY.

.

First turn

off the

saw and unplug

the

power

cord.

Do

the same for

the water

pump.

.

Then remove

water

pump

from

tray.

.

Then

take frame

and motor

assembly out of the

water

tray.

.

Take

tray and drain water

and contents

(sediment)

.

To install

simply reverse

this

process.

NOTE:

THERE ARE

NO ADJUSTMENTS

TO WATER

TRAY

5.

Aliqnment

Procedures

Your

TM-75 tile

saw

is

factory

assembled and

aligned

prior

to shipment

to ensure

accurate cuts

when

your

saw

is

delivered.

However,

since

FELKER

@ cannot

control rough handling

during

shipping,

it

is

suggested

that the

alignment be checked. lf

the saw

is found in

need of adjustment,

refer

to the appropriate

section(s)

below.

There

are

two basic TM-75

alignment

checks. Any

adjustments made

must follow

these

procedures

to

ensure

that the unit functions

freely.

Adjustment

tools required:

Carpenter's

Square and

the small open-end

wrench

provided

with

your

new

saw.

(Fig

3)

1.

Check the Blade

in

Slot Alignment

.

The

blade should

be centered in

the conveyor

cart

slot.

.

Set-up

your

saw

as described

above,

move

the

conveyor caft

back and forth

form the f ront to

the

rear

of the

pan.

lf

the blade contacts either

side

of

the

slot, the

Cart Slot Location

Adjustment

must

be

performed.

Cart

Slot

Location

Adjustment

(See

Parts List,

Diagram

1)

.

Move the

Conveyor

Cart so the Blade is

approximately

midway

between the front and

back

of Cart. Loosen

the three

(3)

Roller

Guide

fasteners

(ltems

6

&

8) with

the

supplied

wrench. Move

the

Adjustment

Clamp

(item

4),

Roller

Guide Bar

(item

3) and Cart together

until

the blade is

centered in

the slot. Tighten

the

fasteners.

lt

is recommended

that

the

Parallel

Alignment

in

step 2 be checked

to

insure

the

best

quality

cuts.

Check the Parallel

Alignment

.

The

conveyor cart

should travel

parallel

to the

plane

of the blade.

.

Place

a square rule

against

the backstop,

lightly in

contact with

the blade. The

blade

surface

should be

parallel

to the square; e.9.,

no

gap

between the

blade and the

square

at

either the front

or back

edge of the blade.

Next,

holding

the square firmly

traverse the cart

fore

and aft. The

blade should remain

parallel

to the square,

staying slightly in

contact with it

throughout its full

travel. lf

the blade does not

stay

in

contact with

the square,

the

Parallel

Alignment

must

be

performed.

Parallel Alignment

(See

Parts

List, Diagram 1 &

Fig 21)

.

Loosen

the

front

two Roller

Guide fasteners

(ltem

6 & 8). Move the Roller

Guide Bar

(item

3) and

Cart by the Adjustment

Clamp

(item

a)

until the square is flush with

the blade. Tighten

the

fasteners

and recheck

the alignment again.

The

cart

should now travel

parallel

to the blade

and the

blade should

be centered

in

the slot.

2.

l3

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19

Kommentare zu diesen Handbüchern

Keine Kommentare