Electrolux EX49XS Bedienungsanleitung PDF herunterladen (Seite 8)

Fig. 20 Fig. 21

8 GB

Provide the cylinder with a gas pressure reducer.

By a hosepipe of 8 mm. connect it to the reducer A, screwed

on the cylinder support B (fig. 19) of the cooker ready for

the connection, arranging then the cylinder in the special

space (fig. 20).

IMPORTANT: follow these guidelines:

1) The flexible hosepipe shall be from 400 mm up to 800

mm. long and conform to the standards.

2) The cylinder support of the reducer shall be faced to the

right side of the cylinder support space.

3) The hosepipe connection to the reducer/cooker cylinder

supports shall be

carried out as indicated

in fig. 20, i.e.: entering

the support place

upright and coming out

from the cooker by the

special back hole. For

the fastening operation

use clamps conform to

the standards.

4) Arrange the cylinder in the special space not in contact

with the oven wall.

5) During the cylinder change, do not remove the tube from

its crossing.

6) Before inserting the cylinder take away the plastic base

as shown in fig. 21.

Fig. 19

Fig. 22

IMPORTANT:

The hosepipe shall not present narrowing and be far

from heat sources, especially the back of the oven.

After the connection, check that the pipes are properly

sealed, using a soapy water solution on the joints.

The flexible hosepipe shall never cross from one side

of the appliance to the other and be visible. In the need

of a connection on the opposite side of the one provided,

ask the manufacturer (see the address in the overleaf)

for additional metal hosepipe D (fig. 20-22).

The additional pipe can be assembled as follows:

a) remove the

tubeholder of fig. 19

and turn the “cross”

coupling C fig. 22.

b) Screw the metal

pipe to the coupling

putting in the seal

G and fix it on the

back of the cooker

by the screw E.

c) Assemble the tubeholder on the other end of the pipe

putting in the seal G.

Carry out the connection by a proper pipe in conformity

with the regulations making sure that it is perfectly put on

the tubeholder and tightened by a proper fixing clamp.

Remark: the gas supply connector of the appliance is a

threaded male 1/2” for round gas pipe and conforms to

UNI-ISO 228-1.

The flexible hosepipe shall be replaced within the date

indicated on the pipe.

Attention: the installer must ascertain that the national

provisions in force have been complied with.

The manufacturer declines all responsibility for the

nonobservance of the above mentioned regulations.

ADAPTING THE COOKER TO DIFFERENT TYPES OF

GAS

In order to adapt the cooker

to a gas different from the one

for which it has been designed,

it is necessary to change the

burners nozzles, to regulate

the air and the minimum.

Before starting with this

operation make sure that the

gas cock has been closed.

1°) NOZZLES REPLACEMENT

a - Cook-top burners

Remove the support grids, the burners and burner caps of

the cook-top. Unscrew the side front screws and back (if

any), remove the knobs and the control panel so that the

cook-top is free; lift it up (consult maintenance chapter fig.11).

Disassemble the Venturi pipes, unscrewing the screws F

(fig. 13). From the nozzles-holder tag (supplied with) chose

the proper injector for any burner and type of gas, following

the indications reported.

By means of a 7 mm socket wrench replace (unscrewing)

the nozzles on the valves. With the cook-top lifted up,

assemble the burners and the burner caps. Regulate the

primary air and the minimum as indicated in chapter 2 and

3. Once the regulations has been carried out as described

in the following paragraphs, seal the regulation elements

and replace the old label on the appliance with the one

reporting the new type of gas.

b - Oven burners

Remove the oven accessories,

the lower plate and unscrew

the back screw D, fixing the

burner to the bottom of the

oven, in order to take it away

and enter the injector (fig. 24)

By means of the socket wrench

of 7 mm. unscrew the

injector.

Once the proper injector has

been assembled, remount the

burner of the oven.

c - Grill burner

It is possible to enter the injector taking away the burner

fixed on the top of the oven by the front screw D (fig. 24).

Change the injector in the same way as per the oven and

reassemble the grill.

It is recommended to put the replaced injector in the proper

accessory kit and preserve them.

WARNING

Check that the gas pressure at the entry of the appliance

is the correct one.

fig. 23

Fig. 24

GRILL

OVEN

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Electrolux EX49XS Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Electrolux EX49XS