Electrolux AOFP102U Anleitung zur Fehlerbehebung PDF herunterladen (Seite 14)

D.1.2 CLEANING THE CABINET AND ACCESSORIES

It is advisable to clean the chamber every week; increasing this

frequency according to appliance use.

Before using the unit, clean all the internal parts

and accessories with warm water and either

neutral soap or products that are

over 90% biodegradable (in order to

reduce the emission of pollutants

into the environment), then rinse

and dry thoroughly. Do not use solvent-based

detergents (e.g. trichloro-ethylene) or abrasive

powders for cleaning. Coat the metal panels with

vaseline oil.

The trolleys must be cleaned with high pressure

water jets.

Drain off the water used in the process of cleaning by removing

the drain plug at the bottom center of the chamber, so that the

liquid flows out into the drain tray under the cabinet. This tray

must be emptied periodically (AOFP061U, AOFP101U,

AOFP102U models).

Refit the drain plug immediately after the cleaning.

Note: make sure the drain tray has been emptied before

removing the drain plug.

ATTENTION: the AOFP201RU model does not have a drain tray.

Make sure the drain hole is connected to the water drain system.

D.1.3 CLEANING THE FOOD (CORE) PROBE

Pay particular attention when handling the probe; remember

that it has a sharp point, therefore handle it with extreme care,

even in the cleaning phase.

You are advised to clean the food (core) probe periodically to

make sure the appliance works at maximum efficiency.

The probe must be cleaned by hand, using warm water and

either neutral soap or products that are over 90% biodegradable

(in order to reduce the emission of pollutants into the

environment), then rinse thoroughly with clean water and

disinfectant solution. Do not use solvent-based detergents (e.g.

trichloro-ethylene) or abrasive powders for cleaning.

ATTENTION: do not use boiling water to clean the probe.

D.1.4 PRECAUTIONS IN THE EVENT OF LONG PERIODS OF NON-

USE

If the appliance is not going to be used for a long period, take the

following precautions:

• Unplug the plug from the electricity mains socket.

• Remove all food from the chamber and clean the interior and

the accessories.

• Rub all the stainless steel surfaces vigorously with a cloth

slightly dampened with vaseline oil, so as to cover them with

a protective film.

• Leave the door partially open to allow the air to circulate.

• Air the premises regularly.

Non-routine maintenance tasks must be perfomed by an

AUTHORIZED SERVICE AGENT.

USE APPROPRIATE SAFETY GEAR

(GLOVES AND MASK) WHEN CARRYING

OUT ANY MAINTENANCE OPERATION.

ATTENTION:

do not touch the appliance if hands

and/or feet are wet. Before

performing any cleaning or

maintenance disconnect the

appliance from the electrical

source and carefully unplug the

appliance. Do not remove safety

guards. Wear protective gloves

when cleaning the condenser. Do

not use scissors, screwdrivers and

sharp objects on the cooling circuit.

D.2.1 PERIODIC CLEANING OF CONDENSER

The condenser can be cleaned with a brush, provided the

bristles are not in steel or a material that can compromise good

operation. Take maximum care not to bend the condenser fins,

as this would cause a reduction in the heat exchange.

If the appliance is to work efficiently, the chilling unit condenser

must be cleaned at least once every 3 months. If the appliance

is installed in a dusty or poorly ventilated environment the filter

must be cleaned more frequently, i.e. about once a month.

The condenser is located behind the front slotted panel. To

remove it, take out the two screws at the bottom and pull it

outwards to release it from the holding clips.

ATTENTION:

Before removing the slotted panel that protects the condenser,

make sure the appliance has been disconnected from the

power source.

Note: The technician is advised to use a brush or vacuum

cleaner to remove the dirt accumulated on the condenser. Do

not use pointed objects, as they may damage the condenser.

ATTENTION: Do not wash the appliance by squirting

a jet of water on it.

D.2.2 CLEANING THE EVAPORATOR

Even in this case cleaning can be done with a brush, provided

the bristles are not in steel or a material that can compromise

good operation of the evaporator. Take maximum care not to

bend the evaporator coil fins, as this would cause a reduction

in the heat exchange.

To access the evaporator battery, proceed as follows:

• Disconnect from the power supply;

• Remove any trays from inside the chamber;

• Remove the 4 screws (2 in front and 2 behind) that secure the

two deflector plates to the evaporator guard;

D.2 MAINTENANCE TO BE PERFORMED

BY TRAINED PERSONNEL ONLY

1 2 ... 9 10 11 12 13 14 15 16 17 18 19

Kommentare zu diesen Handbüchern

Keine Kommentare

Electrolux AOFP102U Anleitung zur Fehlerbehebung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Electrolux AOFP102U