Electrolux FAC124P1A Betriebsanleitung PDF herunterladen (Seite 51)

Section 2 Installation

2-21

Figure 2-62.

Installation Steps - 16” And 17-1⁄2” Deep

1. If wall sleeve does not have a rear grille or louvered

panel, install plastic grille panel from kit. The plastic

grille panel is mounted to the inside of wall sleeve

at the rear flanges. There are (4) plastic nuts in the

flanges of the wall sleeve. If sleeve is missing these

nuts or they are damaged, replacement nuts and

grille mounting screws are supplied with the kit. The

nuts are installed from inside of the sleeve and are

pressed into the square holes of rear flanges. Place

grille against rear flanges and use (4) washer screws

to secure grille to sleeve. (See Figure 2-62)

2. Cut and attach the (1) 1-1⁄2” x 3/8” x 26-1⁄2” long

seal to 25-1⁄2” long. Attach (2) 1-1⁄2” x 3/8” x 14”

long seals as shown. To attach the seals, remove the

backing paper from the seal. Do not touch adhesive.

Press seals firmly in place. (See Figure 2-63)

3. Attach 1” x 3/4” x 14” long seal to the inside of the

grille panel. (See Figure 2-63)

4. Install the new unit into the wall sleeve. Attach the

ground wire to the unit.

5. Install the 1” x 1-1⁄2” x 84” long weather seal

between the wall sleeve and the unit. A flat bladed

screwdriver or putty knife is recommended.

6. Assemble and install the Trim Frame.

Installation Steps - 22” Deep

1. Follow step 1 above.

2. Attach the (2) 4-1⁄2” x 3-1⁄2” x 1-1⁄2” foam blocks

to the inside of the wall sleeve. (See Figure 2-64)

3. Attach 1” x 3/4” x 14” long seal to the inside of the

grille panel. (See Figure 2-64)

4. Cut the 1/8” x 4-1⁄2” x 14-1⁄2” long plastic divider

to 13” long. Slide the plastic divider in the slots of

the (2) foam blocks. (See Figure 2-64)

5. Cut to fit (1) 1-1⁄2” x 1-1⁄2” x 26-1⁄2” long seals as

shown. (See Figure 2-65)

6. Attach (2) 1-1⁄2” x 1-1⁄2” x 14” long seals as

shown. Seals should be flush with front portion of

the 4-1⁄2” x 3-1⁄2” x 1-1⁄2” foam blocks which

holds the plastic divider. (See Figure 2-65)

7. Install the new unit into the wall sleeve. Attach the

ground wire to the unit as shown.

8. Install the 1”x 1-1⁄2” x 84” long weather seal

between the wall sleeve and the unit. A flat bladed

screwdriver or putty knife is recommended.

9. Assemble and install the Trim Frame.

Figure 2-63.

9½”

Step

Figure 2-64.

9½”

Step

Figure 2-65.

9½”

Step

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 139 140

Kommentare zu diesen Handbüchern

Keine Kommentare

Electrolux FAC124P1A Betriebsanleitung Seite 51

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Electrolux FAC124P1A