Electrolux RO400B Bedienungsanleitung PDF herunterladen (Seite 4)

The RO 400 Direct Flow is a very safe appliance, but even so it is important that everyone using

it should be thoroughly familiar with the way it works and its safety features. To prevent mishaps

and problems you should read the "

Safety Information

" on these pages, and carefully follow the

instructions in the "

Installation

" section. Take care of this manual and make sure that it

accompanies the water purifier if it is moved or sold.

SAFETY INFORMATION

• Check that the water you intend to purify meets

the requirements listed under "Requirements of

feed water", in the section "Technical data".

• When the RO 400 is brand-new, the purified

water must not be consumed until after the

calibration and flushing procedures have been

completed.

• Calibration of the RO 400 should only be carried

out:

– the first time that the water purifier is used

– if the appliance is moved to a different place

(locality) where the water quality is different

– after the membrane has been replaced

• When the RO 400 is new or the membrane

contains the special products for storage or

descaling, it will have to be cleaned by following

the "Flushing procedure" before the water from the

water purifier may be used again.

• The water produced by the appliance may only be

consumed if Purification Level indicator II or III

on the control panel was lit when it was being

purified. A green indicator light on the spigot will

come on at the same time.

Do not use the water purifier where the feed

water is microbiologically unsafe or with water

of unknown quality.

• If the feed water supply to the appliance is unfit for

consumption, have the purified water from the

appliance tested after installation. You should

subsequently have the purified water tested once a

year, or if any change in its taste or smell occurs, to

ensure that the water purifier is functioning well.

If the result is unsatisfactory, do not drink the

water. Contact your dealer.

• If any leakage arises, turn off the supply of water to

the appliance immediately and disconnect the

appliance from the electrical supply by removing

the electrical plug from the wall socket, or if

necessary, removing the relevant fuse (or switching

off a circuit breaker) at the electrical distribution

board (consumer unit).

• If the RO 400 is not going to be used for more

than four months, or if the purifier is going to be

disconnected from water and electricity for a long

period (several days), it must be protected by

following th ”Preparing the RO 400 for storage and

protecting it against freezing”.

• Do not attempt to modify or otherwise alter the

RO 400 in any way. Doing so could result in

personal injury and/or damage to property which

would not be covered by any warranty.

• Once every month you should check that the

connections are all watertight. Leakages outside

the appliance cannot be detected by the appliance's

leakage protection system.

• If the water purifier is malfunctioning, it should be

isolated from the electrical supply by removing the

electrical plug from its socket. If this is not

possible, remove the relevant fuse or switch off the

circuit breaker at the electrical distribution board

(consumer unit).

Be sure to follow applicable local plumbing

and sanitary codes when installing the RO

400 water purifier.

• At the end of the appliance's useful life, disconnect

the electrical plug from the power supply, then cut

the electrical lead at the point where it enters the

appliance. Make quite sure that children will not

be able to play with the severed lead and plug.

To find out how best to dispose of the appliance,

contact your dealer or the local authority.

1 2 3 4 5 6 7 8 9 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Electrolux RO400B Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Electrolux RO400B